FiDay 15


Add to cart
Handmade in USAEstimated despatch time of 10-15 business days
SKU: fiday15 Categories:

The BlackFiDay $99 15″ sub is a great budget friendly driver from Fi. Utilizing a high grade single magnet and a heavily bumped back plate as the foundation for a solid subwoofer. A solid core pole with a heavy chamfer  aids in forced cooling of the voice coil.  A 2″ 2 layer aluminum coil provides 19mm of Xmax, ultra low inductance, and a solid 350W power handling.  A cast aluminum basket holds the dual 6.5″ linear spiders and integrated lead under control.  A curvilinear cone and dual layer surround hold up to plenty of abuse.

  • Single 2 Ohm

  • Cast basket

  • Wrap around gasket

  • Curvilinear cone

  • Dual layer foam surround

  • Push terminal

  • Internal lead wire

  • FEA optimized motor

  • 2″ 2 layer aluminum coil

  • Single high grade magnet

  • Linear dual spiders

  • Made in the USA
Weight 15 lbs



Single 2



Thiele-Small Parameters

  FiDay $99 15
Coils SINGLE 2 |
FS 29.8Hz
RE 1.9 Ohms
QMS 5.42
QES 0.41
QTS 0.38
MMS 157 g
CMS 1.853 mm/N
SD 810cm^2
VAS 167.5
SPL 92.1W/1m
BL 11.62
XMAX 19mm (One Way)
RMS 350W

This is a complete list of options; not all options are available on all models.
See drop down selections for options available with each speaker model

P Chamfer: This is a chamfer on the end of the pole, it helps to bring the air down around inside of the motor and helps cool the coil better. It also helps relieve the pressure underneath the dustcap. We recommend at the bare minimum to get this option if you choose this series of woofers.

Hyper Pole: This is an extended version of the standard P Chamfer. It has 1.250” more pole and chamfer resulting in an increased compression ratio for better cooling.

Cooling: Self explanatory, the cooling channels are machined into the inside of the sub to help cool the coil FAR better. But there are some things that you sacrifice. There is less metal inside of the motor so it is a little weaker. If you are looking for a fart/burp only scenario for SPL we suggest that you do NOT get this option. Stick with only the P chamfer. Now if you are looking for a daily sub to beat on and you have less then 2000 watts then this is the option for you. 2000+ watts you need to look into the BTL series.

Flatwind: The flatwire coil option simply helps the power handling of the sub. The coil has more surface area to dissipate heat and will take more power then the regular round wire coil that comes in the ‘stock’ version of the sub. This option will also make the sub tend to be more prone to ‘peaking’. If you are looking to do an SPL install we highly recommend that you use choose the flatwound coil option. In testing it is louder then the regular roundwire coil and takes the thermal abuse much better.

BP: “BP” option which was a machined aluminum compression plug to the pole which helps channel all of the air under the dustcap around the coil for better cooling. To aid with this increased airflow we also added 6 axial cooling channels in the top plate. Along with increased thermal capacity comes the addition of an extra spider and a changed spider pack. All of these features increase power handling from 200-500 Watts depending on the application.

High QTS: This option is for users who intend on using the subwoofer in only a sealed enclosure.

Low QTS: This option is for users who intend on using the subwoofer in only ported enclosures.

Extra Spider: This option adds an additional spider to the spider pack to help with mechanical power handling and keeping the moving assembly under control.

I Heat Ring: This option is a machined aluminum ring in the gap that lowers the inductance of the voice coil which allows it to play up a little higher in the frequency range and have better overall transient response. Please note that you can NOT select low Qts and the I Heat Ring options together.

Internal Lead: This option is for 8 lead coit per coil, increasing the current flow from coil to terminals.

Inner Heat Sink: Its a machined aluminum ring in the gap that lowers the voice coils inductance (allowing it to play up higher and have a little better overall transient response). It also reduces the volume inside the magnet gap of the motor increasing air speed with the cooling as well as allowing the coil to kick off heat to a more receptive thermal mass rather than magnets.

Daily or SPL: Simply put, if you plan on listening to any type of music you MUST choose the daily option. If it is strictly for a fart/burp scenario then choose the SPL option. The reason we have these options is the gap tolerances between the two are different. The gap in the SPL woofer is much tighter and FAR less forgiving in comparison to the Daily option. The Daily option simply gives the coil more wiggle room inside of the gap to deal with the non-linearity tendancys that you can get into when you are using a sub in a daily driving scenario. Typically SPL applications deal with 1 note and it does not change, therefore we can make the gap much tighter and get all of the motor strength that we can out of it.

Spider Spacer: Adding this feature mirrors the spider layers and in turn reduces rock ratio helping keep the voice in line at extreme excursion.

Universal: This option gives you the choice to later chance the impedance of your voice coils. You can change from dual 2s to dual 1s and vice versa by reconing them. If you do not choose this option your motor(s) will be optimized per the coil resistance that you have chosen. (Dual 2s will forever be a dual 2 motor, Dual 1 will forever be a Dual 1 motor).

Dust Cap Type: Choose between a standard or a carbon fibre dust cap. See the examples below…





Subwoofers & Recones are dispatched via FedEx Ground. Small goods such as sticker packs, various apparel items are shipped via USPS. Upon dispatch of your goods, order status will be updated from “test/pack” to “shipped” which is accompanied with tracking details.


    Received my fiday 15 about 2 weeks after ordering. I discovered that they built my sub with a carbon dustcap for no extra charge and without me even asking for it, even though there are no additional options for choosing the carbon dustcap I’ve the regular dustcap. The build quality is so very nice for this budget woofer. I have not yet installed it due to not having built my box yet or having my y wife’s car wired up for the amp yet but i can not wait to get it all together and see how it sounds. I have designed a 3.67 cu ft slot vented box tuned to 30hz for daily music. I wanted to aim for a fairly flat response and designed it in Winisd. So far I am satisfied and feel that for $99 for a budget sub that’s made here in the US it can’t be beat. Thanks Fi for the awesome experience so far and looking forward to purchasing more equipment from you in the near future.

Add a review

Prove you are human! *

Post your comment

Related Products
Select options
Select options
Select options
Select options